Clicky How to Drain Gas from Generator - Solrayo

As an Amazon Associate We Earn From Qualifying Purchases.

How to Drain Gas from Generator

How to Drain Gas from Generator

Dealing with a generator is typically pretty easy. If you’re like most people, the last thing you want to do is mess with your generator’s gas. You just have to make sure that you keep it filled up with gasoline and oil, and then it will run smoothly.

However, sometimes you may need to know how to drain gas from generator for storage or transportation.

This can be a little bit tricky if you don’t know how to do it properly. Here are a few steps to show you how to drain the gas from your generator safely and efficiently.

How to Drain Gas from Generator- Step by Step Guide

When you use your generator, it’s essential to keep up with the maintenance and avoid any deficiencies that could lead to an issue during operation.

Stale gas will likely cause starting difficulties due to inside buildup in this unit so drain away all of its contents at least once every couple of months, if not more often, depending on how often they are used.

The best way to make sure your generator is working at its peak efficiency and never giving out on you in an emergency, it’s essential that the gas inside remains fresh.

If there are times when we’ll be without power for days or longer than two weeks, then take care not to drain all of our stabilization fluid before storing away because this can lead to foam buildup, which will reduce carb throat capacity and thus performance.

To drain your generator safely, you can consider the following steps:

1.    Choose a Location

When draining gas from your generator, be mindful of where you do it. Your location and ventilation are essential factors in how quickly this process occurs.  Make sure you don’t put it anywhere that will create too much noise or fumes because this could hurt someone else.

2.    Twist the Gas Tank Cap

You should always twist off the gas tank cap to allow airflow in there. This will prevent any possible explosion or fire from happening, which would be bad for you or anyone nearby.

Read: Wen gn625i review

3.    Locate the Fuel Valve Switch

Once you find the switch, turn it until there is enough space for your fingers to reach through and push on top of or under where it is located. Your goal here should be getting access so that you can drain any excess fuel from your engine without worrying about cutting off power too soon.

4.    Take Off Maintenance Cover

The fuel valve is located on top of the gas tank, so first, make sure it’s turned off before proceeding. Loosen all large bolts securing your cover and push through with a bit of pressure until it’s free from any obstructions to allow room for movement.

5.    Remove the Clip

Carefully remove the clip on your gas tank, so you don’t spill any when taking off. Once this is done, pinch an aluminum part to get rid of extra fuel and have a rag waiting just in case there’s still some left inside.

Take off the tube attached to the fuel valve, making sure not to lose any of its connections. If this goes wrong and gas starts pouring all over, you’ll have a significant cleanup on your hands.

Read: How long can you run a generator continuously?

6.    Get a Large Container

It’s essential to place the fuel valve in a container large enough to hold 4-10 gallons of gas.

7.    Switch on the Fuel Valve

Once the gas is drained, reconnecting it to its appropriate container can be done in two ways. You could go ahead and screw on that cover again or use helpful tools for a leak-free connection.

8.    Locate the Carburetor

The float bowl is a crucial carburetor component that determines how much fuel can enter it. If you don’t know where to find this screw, look in your shop instruction or owner’s manual book for more info on opening up and maintaining carbs.

9.    Place the Container Below the Carburetor

Once the screw is tight, turn it to open up your drain and let all that gas flow into a waiting container. There should only be enough for you, though. When it’s done flowing in, there’s no need for anything else – just retighten it.

Frequently Asked Questions about Generators

Should I Drain Gas from Generator?

Generators use the same fuel type as cars – regular, unleaded gas. Drain your generator according to directions in its owner’s manual, and be sure you have enough stored for winter before removing any so that it does not corrode its inside during cold months.

How Long Can You Leave Gas in a Generator?

With the help of Sea Foam, ethanol-free fuel, and filling your tank up to its maximum recommended line, you can easily store gasoline in a generator for 1–2 years without worry. This natural gas stabilizer will make sure that you never have an issue again, even if the worst should happen and it runs out just as quickly.

Is There a Drain Plug on a Gas Tank?

Gas tanks are known not to have drain plugs. The best way to drain your gas tank is with a special tool that has been designed for just this purpose. It’s called “the draining hose” and can be found under the filter on top of it, near where you would park if not driving.

So there you have it! Your very own step-by-step guide on how to drain gas from your generator. Gas generators can be a lifesaver when the power goes out, but they can also be dangerous if not used properly.

Draining gas from your generator is a process that may seem daunting at first, but with a little know-how and some handy tips, you can do it like a pro.

We hope this post was helpful and informative – please feel free to share it with your friends and family who might find it useful too. And as always, if you have any questions or comments, please don’t hesitate to let us know in the comments section below. Happy draining.

Read: Problems with Westinghouse generators

Leave a Comment

Your email address will not be published.

Scroll to Top